cart Shopping Cart YOU HAVE (0) ITEMS
SAME DAY, $5 FLAT RATE SHIPPING*
FULL NZ WARRANTY ON ALL PRODUCTS
2142

Accusharp Knife Sharpener

DFS_accusharp

$38.00 $28.00 Save $10.00 GST Incl - NZ purchases only
Qty.

Accusharp Knife Sharpener

AccuSharp Knife and Tool Sharpener (001) Finally, a Knife Sharpener anyone can use! No more messy oils or stones. In about 10 seconds, sharpen knives, (even serrated knives), cleavers, axes, machetes, and many accusharp1other cutting tools. The large ergonomic handle fits either hand safely and securely. The full length finger guard protects your fingers. Sharpening blades are Diamond Honed Tungsten Carbide for years of reliable use. AccuSharp Knife Sharpeners will not rust and can be cleaned with soap and water or in the dishwasher. Replacement sharpening blades are available. Sportsmen, Cooks, Craftsmen, Gardeners, and many more, all need the easy-to-use, affordable AccuSharp line of knife and tool sharpeners.

To Sharpen Knives:
To use, place knife on table or counter top with the cutting edge up and with about 1/2” of the blade tip extending past the edge of the table as shown in the illustration.

While holding the knife handle with one hand, hold the AccuSharp® as shown with your fingers through the opening formed by the handle and the finger guard.

REMEMBER: THE SHARPENER MOVES WHILE THE TOOL BEING SHARPENED 

Accusharp sharpener

REMAINS STATIONERY.

Straddle the knife’s cutting edge near the handle of the knife with the “V” notch formed in the sharpener. With the head of the AccuSharp® at about a 90° angle to the knife’s edge press down LIGHTLY using thumb pressure and draw the AccuSharp® past the point of the blade. You will feel the tungsten carbide sharpeners removing metal from the knife.

Several passes in this manner may be required before your knife’s cutting angle conforms to the proper angle of AccuSharp®. Once that angle is achieved then two or three passes should be sufficient to bring your knife back to a sharp edge.

REMEMBER: LIGHT PRESSURE IS SUFFICIENT. Heavy pressure might cause you to lose control of the knife and possibly cause injury.


To change Blades:
The tungsten carbide sharpeners of AccuSharp® are of high grade industrial quality and are one of the hardest materials known. Even so, after several years of use, they may become worn. Due to their unique design the sharpeners can be reversed for double life.

To reverse the sharpeners lay the AccuSharp® on its side with the screws up. Remove the screws and carefully separate the two halves of the handle as shown in the following illustration. The sharpeners should remain in the lower half. Simply switch the position of the sharpeners (front sharpener to rear and rear sharpener to front) taking care to keep the reference dot (n) on the sharpeners facing toward the tail end of the handle. If the finger guard becomes disengaged during this operation, secure both ends of it in the slots provided prior to reassembly.

CAUTION: DO NOT REASSEMBLE THE KNIFE SHARPENER WITHOUT THE FINGER GUARD. SERIOUS INJURY MAY RESULT. Reassemble the two halves of the handle and secure with the three screws.

DO NOT OVER TIGHTEN SCREWS. The factory torque setting is about 5 inch pounds of pressure. Tighten them only until you feel increased resistance. If sharpener has any cracks around the screw heads ­do not use it. Either discard the sharpener or return it under the terms of the warranty.

AccuSharp® is perfectly safe when used properly. As a precaution, the knife blade should be thoroughly cleaned after sharpening.

Testimonial:
Bill Hinners
"I started using AccuSharp years ago. I used to use a stone and steel all the time before finding the AccuSharp sharpener. This product sharpens pretty much any knife at the perfect angle and very quickly. It only takes a couple of passes and it makes the knife like a razor. I always keep it right by my side. A few years ago, I went out and picked up a bunch of them for my family for Christmas presents. That's what brought us to your webpage this holiday season, my wife was looking for a location near here where she could purchase one for her sister. I highly recommend the product!

"I am a chef at Yale University, where I've cooked for over 20 years. I graduated from the Culinary Institute of America and got my Bachelor's degree from the University of New Haven. I've worked several restaurants and country clubs in CT. Besides working at Yale, I also lead the Food & Wine Community on Prodigy."

MADE IN USA

KEYWORDS:
Accusharp Knife Sharpener, accusharp, knife sharpener, tungsten sharpener, knives,

You might also be interested in ...